1. Home
  2. Manufacturers
  3. UMAX
  4. Scanner
  5. UMAX 1210P Driver
  6. Reviews

UMAX 1210P Driver Reviews

User Reviews and Ratings

Only reviews are shown below.  Ratings submitted without a review are used in calculating the total ratings shown above, but will be displayed below.

3 of 4 people found the following review helpful:
Tom Harris
Tested on Windows XP
13 Sep 2005
 

Installation: 4 out of 5
Stability: 4 out of 5
Compatibility: 4 out of 5
 
"Installation went fine.

Works well, except there seems to be a file size limitation on scans - so have to use low resolution: RGB copy of an A4 sheet not always successfull - sometimes only get about 2/3rds of page or one side of page is truncated so that top third is in the place of bottom third and bottom third is at top."

spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
Jon
Tested on Windows 2000 Professional
9 Jun 2005
 

Installation: 5 out of 5
Stability: 5 out of 5
Compatibility: 5 out of 5
 
"I'm pleased to say that this works with Windows 2000 professional as well. Just follow the instructions in the Uploader notes above, except "Legacy support for PnP" is "Enable legacy plug and play detection" in Win 2000. Ignore what it says about EPP."
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
redlaws1
Tested on Windows XP
6 Mar 2005
 

Installation: 1 out of 5
Stability: 1 out of 5
Compatibility: 1 out of 5
 
"it was a corrupt zip file"
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
TomZ

9 Feb 2004
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"I am having the same trouble as Alan. Did that ever get resolved? I adjusted port settings to EPP, loaded 610P driver through XP and installed downloaded scan utility. I am trying to access through Adobe Photo Deluxe 4.0. The scanner shows up on the scanner list but is not recognized. I get the following message, "Program was unable to find your scanner. Please e
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
richard

12 Jan 2004
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"Alan, which application are you trying to use the scanner with?

I assume you've installed the 610P first this should install a useable twain driver. Uninstalling scanners often leaves the twain drivers behind - I would uninstall all scanners and check you have no twain DLL libraries in the windows directory (do a find files called twain*.* in c:\windows) then reboot an

spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
Alan

11 Jan 2004
 

Installation: 5 out of 5
Stability: out of 5
Compatibility: 1 out of 5
 
"Well, I tried all that you suggest, adjusted port settings too, still can't access scanner - "Program was unable to find your scanner, please ensure that scanner is connected and drivers are installed" followed by "Cannot start TWAIN driver! please ensure successful installation of hardware and drivers"

Any thoughts?"

spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
richard

7 Jan 2004
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"The setting of port LPT1 to EPP may only be accessible in the BIOS settings of the PC - this was Graham's problem below and changing it from ECP to EPP has sorted it out."
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
Graham

18 Nov 2003
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"I am using XP home and could not get the scanner to be recognised. I installed the UMAX 610P driver and then attempted to change the LPT1 settings. However I have the following settings "Use any interrupt assigned to the port" that I ticked Enable legacy plug and play detection that I also ticked, but here I only see a choice of LPT1, LPT2 or LPT3 (I left LTP1), there i
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
franz alias computer-franz

16 Jul 2003
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"I am happy, many Thanks for yuor comments and instructions, they are easy and finest."
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
Geoff

18 May 2003
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"Hey, hey, what do you know, it does work and first time what's more. Thanks very much Richard"
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
ayosha

25 Mar 2003
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"Doesn't work on XP Home 2000 for 1220p"
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 
3 of 4 people found the following review helpful:
MikeKipp

21 Feb 2003
 

Installation: out of 5
Stability: out of 5
Compatibility: out of 5
 
"Very clear instructions. Worked perfectly fist time. Thanks."
spacer
Was this review helpful? Yes, it was helpful No, it was not helpful (Report this)
 

Add Your Review

Ratings & Reviews may be submitted after downloading and using or attempting to use the driver or firmware.

This website is not affiliated with UMAX. All company names/logos are properties of their owners.
Copyright © 1996 - 2024 DriverGuide is an iCentric Corporation Company.    All rights reserved.
Privacy Policy
server: ftp, load: 6.01