RCA Corp RD1071 Driver Download (Official)

Download the latest version of the RD1071 driver for your computer's operating system. This update - "RD1021_71_75FWUpgrade_v1607.exe" - has an average rating of 4 out of 5 stars based on 6 reviews, and has been downloaded 101 times. The total disk space used for this update is 2.1 MB.

6 Ratings, (see all reviews) 101 Downloads

Official Source - Manufacturer Website

Find All RCA Corp RD1071 Driver Updates

Supported Models

RD1071

RD1075

Manufacturers

RCA Corp

Supported Operating Systems

Not Applicable

File Name

RD1021_71_75FWUpgrade_v1607.exe (2.1 MB)

Versions

1.607 (14-Apr-2004)

Additional Notes

Secure WMA Playback support for online music services plus USB Drivers!

FIRMWARE UPGRADE STEPS

DO NOT CONNECT YOUR LYRA? RD1021/RD1071/RD1075 until step #6.

Before running the firmware upgrade, please remove (uninstall) all previous versions of the Lyra? "upgrader" for your device by following these steps:

From the Windows "Start" menu, open the "Control Panel." ("Start" > "Settings" > "Control Panel" in some Windows OS's.)

Select "Add or Remove Programs." ("Add/Remove Programs" in some OS's.)

Find and remove all of the following software, if they exist:

*"Lyra? Personal Audio Player (RD1021/71)&a

mp;quot;

*"Lyra? Personal Audio Player (RD1071/75)"

*"Lyra? Personal Audio Player (RD1021/71/75)"

Additionally, from the Windows "Start" menu:

Select "Programs."

Select "Lyra? Personal Audio Player." If this does not exist, skip to #4.

If a sub folder exists with the name(s) of:

*RD1021, RD1071

*RD1071, RD1075

*RD1021, RD1071, RD1075

Run the "Uninstall" from each folder.

Re-boot your PC if requested to.

Locate the downloaded RD1021/1071/1075 upgrade file and double click it.

Allow the program to completely install all USB drivers as well as the upgrade program and firmware. You may be required to reboot once the install is complete. IF YOU GET A BOX THAT SAYS "CONFIRM UNINSTALL", "Do you want to completely remove the selected application and all of its components?" you will need to click "yes", allow it to complete the maintenance, reboot your computer, and go back to step #3. This will only be necessary once.

Make sure your Lyra? RD1021/1071/1075 device is powered off and connect it to the PC using the USB cable.

*VERY IMPORTANT* On the Lyra? RD1021/1071/1075, press and hold the "Play" switch for at least 5 seconds. (This will put the Lyra? RD1021/1071/1075 device into Recovery Mode, which is only necessary for firmware upgrades.) The LCD will remain off/blank. Depending on your Windows OS, there may be no response or your PC might find a "STMP3410" device or other such new device. The new drivers will be located and installed for the device. If you are requested to reboot, please do so.

From the "Start" menu, select "Programs" > "Lyra? Personal Audio Player" > "RD1021, RD1071, RD1075" > "Update Device."

After the program is finished searching for the device, drivers and new hardware may be detected and installed. (You may get an information box that reads, "media state is not initialized." Click "OK" to continue.) Then the "Update Lyra? (RD1021/1071/1075) Device" box will pop up with current version and new version of firmware shown.

Press "Start" to update the firmware of your Lyra? RD1021/1071/1075. Depending on your existing firmware version, the Upgrader might show an option for formatting the device. Click "Yes" to continue.

When the update is complete, click "Close." If present, use the Windows system tray icon to safely disconnect the Lyra? RD1021/1071/1075 and unplug it from the USB cable.

You can now check the version of the firmware by entering the following sequence.

Press "Play" to turn the Lyra? RD1021/1071/1075 device on.

Press "Stop" to stop playback.

Press "last" (<<), "next" (>>), "last", "next", "last", "next", "Vol Down".

The display should now fill with squares, and then read "v.1.607 test mode" if the upgrade was completed successfully. Press "Stop" to exit the test mode. If the unit does not display the test mode, turn it off and on and repeat #12C. If it shows a version lower than 1.607, you will need to re-run the program from steps 6 above

See Less

Uploaded By

Nagarajah (DG Staff Member) on 5-Apr-2005

Ratings & Reviews

See all RCA Corp RD1071 ratings and reviews

Related Driver Updates

RCA Corp RD1071 Driver Update Utility	Install the driver automatically
RCA Corp DCM245R Driver	Install the driver automatically	Download driver
RCA Corp RCA USB Cable Modem Driver	Install the driver automatically	Download driver
RCA Corp RCA USB Cable Modem Driver	Install the driver automatically	Download driver
RCA Corp RD1021 Driver	Install the driver automatically	Download driver

How to Update RD1071 Device Drivers

Step 1 - Download Your Driver

To get the RD1071 driver, click the green download button above. After you complete your download, move on to Step 2.

If the driver listed is not the right version or operating system, search our driver archive for the correct version. Enter RCA Corp RD1071 into the search box above and then submit. In the results, choose the best match for your PC and operating system.

Tech Tip: If you are having trouble deciding which is the right driver, try the Driver Update Utility for RCA Corp RD1071. It is a software utility which automatically finds and downloads the right driver.

Step 2 - Install Your Driver

After you get your new driver, you need to put it on your computer. On Windows, there's a tool called Device Manager that helps with this. It shows you all the parts of your computer and the drivers they use. To finish setting up the new driver, you'll probably need to turn your computer off and on again.

Tech Tip: Driver downloads and updates come in a variety of file formats with different file extensions. For example, you may have downloaded an EXE, INF, ZIP, or SYS file. Each file type has a slighty different installation procedure to follow.

For more help, visit our Driver Support Page for step-by-step videos on how to install drivers for every file type.